Industries

Modern vacuum technology increases energy efficiency during vulcanization

ContiTech Antriebssysteme GmbH (ContiTech Power Transmission Group) was able to significantly increase the energy efficiency of its vulcanization systems by using the latest vacuum technology for degassing the molds in vulcanization boilers.
( PR4US.com | Press Release | 2020-02-05 12:34:18 )
Previously, only liquid ring vacuum pumps were used in all systems – until testings started with Mink claw vacuum pumps from Busch at the beginning of 2017. The results were astounding, proving that neither water nor other operating fluids are required and that energy consumption is radically reduced.

As a manufacturer of the entire spectrum of drive belts, ContiTech offers a comprehensive range of rubber belts used in practically all industrial applications. The belts are manufactured in vulcanization systems consisting of several autoclaves. Depending on the size of the vulcanization systems, one vacuum pump can be connected to one system or several systems can be supplied with vacuum simultaneously by a single vacuum pump. Operations are carried out in three shifts in batch mode. This means that the vacuum pumps are permanently in use around the clock.

Liquid ring vacuum pumps were originally used for degassing the rubber mass. Because the central cooling water network at ContiTech Antriebssysteme reached the limit of its capacity, Anja Horn, who is responsible for energy efficiency, analyzed the individual water consumers in the plant. On average, the liquid ring vacuum pumps consumed about seven cubic meters of water per hour. In addition, a container with a fresh water reservoir was installed on each vacuum pump. Due to rapid contamination, the water had to be replenished or replaced with fresh water on a regular basis. In addition to the high water consumption, the high water temperatures had a negative effect on the cycle and the supply. As a result of excessive water temperatures, the desired vacuum level of 200 millibar in the autoclaves could not always be achieved. The reason for this is that the vacuum to be achieved in a liquid ring vacuum pump depends, among other things, on the water temperature. Liquid ring vacuum pumps only reach their optimum vacuum level at a water temperature of 15 °C.

The liquid ring vacuum pumps used had a power consumption of six kilowatts each. As the vacuum pumps operated in three shifts seven days a week, each machine worked a total of 8,000 operating hours per year. This corresponded to 48,000 kilowatt hours per year.

Maintenance was looking for a technical solution to reduce both energy and water consumption. It was also important to improve reliability as much as possible. If, for example, a leak in the system caused vapor to enter a liquid ring vacuum pump, they reached their capacity limits and the vacuum level in the autoclaves deteriorated drastically. In the past, an average of one liquid ring vacuum pump per year had to be replaced because the vulcanization process caused deposits and corrosion in the vacuum pumps.

ContiTech found an alternative to its previous vacuum generation approach in the Mink claw vacuum pump from Busch. As early as 2017, a Mink claw vacuum pump was installed in a vulcanization system for test purposes as an alternative to a liquid ring vacuum pump. Mink claw vacuum pumps do not require water or any other operating fluid to generate vacuum. The reason for this is the completely contact-free operating principle, which enables dry compression, meaning compression without the use of operating fluids. For ContiTech Antriebssysteme, this meant no more costs for the operating fluid water and the associated operating costs such as refilling, replacing, treating and disposing the water.
Added to this are the savings in electricity costs. With nine kilowatts, the Mink claw vacuum pump has a larger motor than the liquid ring vacuum pump previously used. However, Mink's variable speed drive adapts the motor frequency to the actual demand. In normal operation, the motor sometimes only runs at frequencies of around 30 Hertz. This means that it requires about three kilowatts at this frequency. However, if vapor is suddenly sucked in due to a leak, the Mink vacuum pump immediately increases its rotational speed and thus its pumping speed so that the required operating pressure of 200 millibar can always be maintained.
Thus, average power consumption can now be estimated at four kilowatts. Projected over one year, this corresponds to a consumption of 32,000 kilowatt hours. Compared to the previously used liquid ring vacuum pump, this is a reduction of 16,000 kilowatt hours per year. ContiTech Antriebssysteme GmbH tested the first Mink claw vacuum pump very carefully and analyzed its performance and energy costs precisely. Even before the end of the test phase, ContiTech had decided to purchase three more Mink claw vacuum pumps and operate them on vulcanization systems. The aim now is to gradually install Mink claw vacuum technology on all vulcanization systems in order to guarantee maximum reliability and efficiency in the future.


Press Information


Published by

Jasmin Markanic

+49(0)7622 681-3376
Schauinslandstrasse 1
79689 Maulburg - Germany
http://www.buschvacuum.com

Contact Jasmin Markanic


 

 

 

 

 

 

Disclaimer: If you have any questions regarding information in this press release please contact the company added in the press release. Please do not contact PR4US. We will not be able to assist you. PR4US disclaims the content included in this release.
Preparing for PR: Five Hot Tips for Startups
PR Fundamentals for Startups - MaRS Best Practices
Public Relations 101
Public Relations Strategy in Our World Today!
Introduction to Public Relations
Trends in Communicating
How to Do Marketing/PR on a Budget - CoInvent Startup Summit 2014 New York
Monika Dixon Shares PR Tips